01/What’s in the Box
02 / Camera Overview
| Tlaฤรญtko napรกjenรญ | Press and hold for 5s to power on/off the camera. |
| Tlaฤรญtko Reset | Press and hold for 5s until hearing ‘Boogu’ toreset or restore to factory setting |
| Slot pro kartu SD | Support local SD card storage (up to 128G) |
| Kontrolka pracovnรญho stavu | Solid on red: Network is abnormal Slow flickering red: Awaiting Wi-Fi connection. Start adding devices WIFI fast flickering red: Wi-Fi connecting Solid on blue: Wi-Fi connected successfully. The camera is running normally. |
03 / Setting up the Floodlight Camera
Stรกhnout aplikaci 'ieGeek Cam'
Method 1: Download the ieGeek Cam APP from the APP Store (iOS) or Google Play(Android);
Metoda 2: Naskenujte QR kรณd aplikace ieGeek Cam a stรกhnฤte ji.
Registrovat รบฤet
New users need to register by email. The concrete steps are as follows
1. Click “Registerโ;
2. Follow the steps to complete the registration of the account;
3.Pลihlaste se.
Poznรกmka:
1. When registering a new account, please choose the region which you are actually in and the correct country code. (Different registered regions can’t share the camera.)
2. Please choose to register by e-mail.
How to Add a Camera to APP
Pลed pouลพitรญm:
1. Please insert the Micro SD card before powering it on; otherwise, the SD card cannot be detected.
2. Put the camera and smartphone 1-3 ft (30-100 cm) away from the router to set Wi-Fi.
3. Zkontrolujte, zda fotoaparรกt pouลพรญvรก 2,4GHz Wi-Fi.
Note: If it can’t be powered on, please plug in DC 5V 2A power adapter to charge the camera for 15min first.
Charge the Battery
Pay attention to:
Always keep the USB charging port covered with the rubber plug after charging the battery for better weatherproof performance. When connecting to the solar panel, you don’t need to open the rubber cover completely; just open the smaller USB part of the rubber cover to connect.
04 / Mounting the Floodlight Camera
Find a Good Mounting Spot
To find a spot to mount this floodlight camera, you need to test the signal strength
1. Open the ieGeek Cam app go to installation Guide>Network Diagnostic.
2. To test the wireless signal strength, take your camera and phone to the location where you want to mount the camera.
3. Move the camera as close to the router as possible if the wireless signal strength is poor.
Select Height and Location
Hang ieGeek Camera 7-10 ft (2-3 m) above the ground. This height maximizes the detection range of the motion sensor of the ieGeek Camera. Avoid placing the ieGeek camera under direct sunlight.
Note: If a moving object approaches the PIR sensor vertically, the camera may fail to detect motion.
- Nesmฤลujte fotoaparรกt k ลพรกdnรฝm objektลฏm s jasnรฝm svฤtlem, vฤetnฤ sluneฤnรญho svitu, jasnรฝch svฤtel lamp apod.
- Do not place the camera near any outlets, including the air conditioner events, humidifier outlets, the heat transfer vents of projectors, etc.
- Kameru neinstalujte na mรญstech se silnรฝm vฤtrem.
- Nesmฤลujte fotoaparรกt k zrcadlu.
- Aby nedochรกzelo k ruลกenรญ bezdrรกtovรฝch sรญtรญ, udrลพujte fotoaparรกt ve vzdรกlenosti alespoล 1 metr od jakรฝchkoli bezdrรกtovรฝch zaลรญzenรญ, vฤetnฤ routerลฏ Wi-Fi a telefonลฏ.
05 / Notes on PIR Motion Sensor
Dosah detekce ฤidla PIR
The PIR detection range can be customized to meet your specific needs. You may refer to the following table to set it up in Device Settings via “ieGeek Cam’App.
| Citlivost | Detekฤnรญ vzdรกlenost (pro pohybujรญcรญ se a ลพivรฉ objekty) |
| Level1-3 (Low) | Up to 4-5 meters |
| รroveล 4-7(Med) | Aลพ 5-8 metrลฏ |
| รroveล 8-10 (vysokรก) | Aลพ 8-10 metrลฏ |
Note: The detection range would be wider with higher sensitivity, but it would lead to more false alarms. It is recommended to set up the sensitivity level to โLow” orโMid” when you install the camera outdoors.
06/FAQs
For more detailed FAQs, please log in to the app and search “Me”-โFAQ”-“Help &Feedback-Battery Camera.
The device prompts offline.
1. Zkontrolujte, zda je zaลรญzenรญ v zapnutรฉm stavu, a sledujte, zda pracovnรญ kontrolka zaลรญzenรญ normรกlnฤ svรญtรญ.
2. Check whether the Wi-Fi network is in good condition and restart the router.
3. If the device is located far away from the router, which results in the inability to obtain a good Wi-Fi signal, it is recommended to move the router to a closer place or add a Wi-Fi amplifier to improve the Wi-Fi performance of the home.
4. Delete the camera from your ieGeek Cam account and add it again after resetting the device.
Check whether the device firmware and application program are the latest version.
Aktualizace smฤrovaฤe nebo hesla Wi-Fi?
Delete the camera from your ieGeek Cam account. After resetting the device, use the new Wi-Fi and password to add it again.
Can’t play historical video?
1. Check the status of the SD card in “Settings to ensure that the SD card has been successfully recognized.
2.Reinsert the SD card.
3. In the application, format the SD card.
4. Try another new SD card.
ฤastรฉ stisknutรญ budรญku?
1. In the app, lower the sensitivity of the motion detection alarm
2. Check whether there are objects that interfere with and trigger the PIR sensor in the field of view of the device, such as the outdoor unit of the air conditioner driving cars, passing pedestrians, etc. The angle of the device can be adjusted appropriately to avoid these easily disturbing objects
3. Turn on “detection” and use a humanoid algorithm to filter useless alarms.
The phone cannot receive the alarm push.
1. Turn on all the push permissions of the “ieGeek Cam’ application in the systems settings of your mobile phone.
2. Make sure that the device motion detection function is successfully turned on
3. Restart the phone and clear the cache on Android phones.
4. Check whether the network is good.