Note: Manual contents are subject to change without notice inaccordance with our polivy of continuous product improvement.
1. Charge your doorbell with your phone charger.
Plug in the charger
Please charge your doorbell with a USB-compatible phone charger(not provided) and the provided charging cable. The LED indicator near the MicroUSB port will glow blue once fully charged.
2. Supply power to the chime.
Powered by three AA batteries
Three units of AA batteries are required to make your indoor chime 100% wire-free. And you will be free to place your chime in almost anywhere indoors
Please mind the electrodes when installing batteries!
Powered by DC5V Charger.
You can also plug in the provided USB cable and connect the chime to your DC 5V 1A~2A phone charger.
3.Set up your doorbell in the CloudEdge app
Download the CloudEdge app
Search ‘CloudEdge’in the app stores or scan below QR codes to download the app
Switch on your doorbell
Remove the wall mounting bracket and the right-side silicone cover, and switch on the power for your doorbell. The LED indicator around the doorbell button will be red (once per second), and it is ready for network setting
Set up your doorbell.
In the ‘CloudEdge’ app, log in or create a user account to log in. Tap select Doorbell, and complete the setup following the in-app instructions
Tips:
1). Please operate the setup near your Wi-Fi router.
2). Make sure your phone is connecting to a 2.4GHz Wi-Fi
3). Make sure the doorbell is turned on and its indicator LED is flashing red. If not, press and hold RESET for 5 seconds.
4). Ensure the Wi-Fi signal is good, and the Wi-Fi password is correct.
Doorbell indicator explanation.
4. Connect the indoor chime
Click the reset button.
Click RESET on the chime, and the chime indicator on the left will flash red for 20 seconds, indicating that the chime is in pairing mode
Press your doorbell to pair up
Press the doorbell button to send a pairing signal, and your chime will sound to react, together with its blue LED flashing. Chime pairing succeeds
Chime settings.
Ringtone selection.
Click to change ringtone (4 ringtones available)
Volume control button.
Click to control volume:
level 1: 110 dB;
level 2: 100 dB;
level 3: 90 dB;
level 4: 80 dB
Settings
Click to enter/quit pairing mode; Press & hold for 5 seconds to restore factory defaults
5. Install your smart doorbell
Select a location.
It is suggested to mount the doorbell at least 4 feet (120 cm) above the ground for optimal angle of view and best motion detection performance.
Install at an angle (Optional)
You can purchase the following angled brackets so as to point your doorbell to a specific view angle.
Mark the screw holes
Take apart the wall mount from your doorbell and use it as a template, mark the location of the two mounting holes on your wall.
Install the wall mount
Screw your bracket into the wooden wall with the provided mounting screws.
if installing on stucco, brick, or concrete, drill holes in your wall, then insert the included anchors before driving in the mounting screws
Mount your doorbell
Attach your doorbell to the mounting bracket and then snap the doorbell to make sure it reaches the bottom. Then secure it with the provided star-shaped security screw, using the provided screwdriver bit
One more thing
Kindly note the anti-theft alarm in the doorbell settings
Tamper alert on
Once the doorbell is detached from the bracket, a 30-second alarm will be triggered. Meanwhile, video recording will be activated, and alarm notifications will be pushed to the owner’s APP account.
Tamper alert off
The owner can disable the tamper alarm in doorbell settings and detach the doorbell for battery recharging or maintenance
12. Product Specifications
Video Doorbell Model No.:Bell J7
Camera | Full-HD Camera |
Effective pixels | 1920(H) x 1080(V) |
IR LED | High power dot-array IR LED x 1 |
View angle | 145° |
Motion detect range | 100° (Max 5m) |
Motion sensitivity | 5 level sensitivity settable |
Alarm trigger | Call button, motion detect, anti-theft alarm |
Wi-Fi | 2.4 ~ 2.4835 GHz WIFI (IEEE802.11b/g/n) |
Video recording | Video clips against events |
Audio | Full duplex 2-way audio |
Storage | SD card (Max. 128G) |
Cloud storage | Yes (7-days-free trial) |
Power supply | Built-in rechargeable Li-ion battery |
Battery capacity | 4,500mAh |
Ingress protection | IP65 |
Operating Temp. | -10℃ to 50℃ |
Dimensions | 34.5 x 56 x 134.6mm |
Net weight | 125.8g (Battery Included) |
Wireless Chime Model No.: Chime06
Power source 1 | DC 5V 1A (from Micro USB) |
Power source 2 | AA LR6 1.5V battery x 3 units |
Consumption | 0.4W |
Ringtones | 4 ringtones optional |
Connection type | Radio frequency 433MHz |
Place of use | Indoor |
Blue LED flashing | Pairing mode |
Red LED flashing | Working normally |
Blue LED flashing twice | Reset factory default succeeds |
Working Temp. | -10℃ ~ 50℃ |
Humidity | <90%, no condensation |
Dimension | 75.5 x 75 x 28mm |
Weight | 70g (Exclude batteries) |