FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1)This device may not cause harmful interference
2) This device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement: The equipment complies with FCC Radiation exposure limits set forth for uncontrolled environments. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
FCC ID: 2AG7C-BABYIT(Camera)
FCC ID: 2AG7C-BABYIM(Monitor)
01/Overview
02/Download ‘ieGeek Cam’ APP
Method 1:
Download the ‘ieGeek Cam’ APP from the APP Store (iOS) or Google Play(Android)
Method 2:
Scan the QR-Code to download the App
03/connect the Camera to the APP
The camera can be connected to both the monitor and the app. Generally, it is connected to the monitor by default.
Follow the steps below to connect the camera to the App:
- 1. Make sure the Wi-Fi network is a 2.4 GHz network. as the camera doesn’t support 5GHz Wi-Fi.
- 2. Download the ieGeek cam App on your phone. Register a new account to log in or log in directly.
- 3. Use the needle to reset the camera for 5 seconds until you hear the ‘BOOGU’ beep, which means the camera has been reset; after 10-20 seconds, you will hear another beep, and the red light of the camera blinks slowly.
- 4. Follow the step instructions on your smartphone to add the camera, and scan the QR code with your camera.
04/connect the Camera to the Monitor
Turn on the power of the camera and the monitor, and then the camera will automatically connect to the monitor.
Note: If the connection to each other is not successful the first time, please use the needle to reset the camera and reconnect the monitor after the second beep of the camera. The connection is distance-limited, so make sure the distance between the camera and the monitor is no more than 300m.
Disconnect the camera from the monitor
- 1. Press the Menu button on the display screen, and select setting > Camera.
- 2. Long press the ok button on the display screen to release the binding.
Reconnect the camera to the monitor
1. Press the Menu button on the display screen, and select setting> Camera.
2. Long press the camera Pairing button until you hear the prompt tone
3. Press the ok button on the display screen to start pairing.
Note: If you have problems with connection, please feel free to contact [email protected] for one-on-one customer service guidance.
Connect two cameras to the monitor.
Follow the step above to connect the two cameras in turn. Two screens will appear on the monitor.
Press the back key for camera selection(a small camera icon flashes on the screen).
Press ←or→ for camera selection, then press the ok key to remotely control the selected camera (split view).
Press the ok key again to enter the selected camera in full-screen mode.
Press the back key to reselect the camera.
05/General Settings
Set up volume
1. Press Menu button on the display screen, and select and press ok to enter the interface
2. Press the UP and DoWN direction buttons to adjust the volume.
Set up brightness
1. Press the Menu button on the display screen, select, and press ok to enter the interface.
2. Press the UP and DOWN direction buttons to adjust brightness.
Set up time
1. Press the Menu button on the display screen and select Date and Time.
2. Press the Direction buttons to change the date, time, and time displaying mode.
Set up language
1. Press the Menu button on the display screen and select Language
2. Select the language you need
Set up sleep mode.
You can set up sleep mode to increase standby time.
1. Press the Menu button on the display screen and select Sleep mode.
2. Select Sleep mode as 1 minute, 5 minutes, 10 minutes, 30 minutes, 60 minutes or off.
Setting camera status indicator
1. Press the Menu button on the display screen, select and press the ok button to enter the interface
2. Press the left and right arrow keys to select on or off.
SD card
1. Press the Menu button on the display screen, and select > SD card management. Then, you can view the total capacity and remaining capacity of your SD card.
2. (Optional) You can format the SD card as you need, but make sure that the important data is backed up.
Note:
This product does not support hot-swapping.
Please insert the SD card before powering it or unplug it after power off.
Upgrade
Make sure your camera is connected to a 2.4 GHz Wi-Fi. You can upgrade your camera when the upgraded alarm appears. Or press the Menu button on the display screen and select Device information to check whether it needs to be upgraded.
Low battery alarm
When the camera is low on battery, the low battery alarm will appear on the display screen. Please change the display as soon as possible.
Motion Tracking & Alarm Area
1. Motion Tracking: Open the ieGeek cam app, click your device, click the pinion icon in the upper right corner, select Motion Tracking, and open it.
2. Alarm Area: Open the ieGeek cam app, click your device, click the pinion icon in the upper right corner, and select Alarm Management>Motion Detection>Alarm Area.
Onvif Settings
Open the ieGeek cam app, click your device, click the pinion icon in the upper right corner, and select Onvif Setting, and set a password to enable this function.
06/FAQ
Q: The monitor cannot be previewed properly?
A:
Check whether the monitor has been connected to the camera. If not, pair the camera and the monitor first.
Q: Cannot find the pairing button?
A:
The pairing button is the call button of the camera. Long press the button for 3 seconds, and follow the step instructions of the display. (To enter the pairing interface of the display, press the Menu button on the display screen and select Camera Management.)
Q: What if the monitor screen is stuck and it doesn’t work while pressing any buttons?
A:
Reset your monitor with the needle, and then long-press the power button of your monitor to restart it.
Q: Why can’t I get the notifications with my cell phone App when I connect the camera to the monitor?
A:
Please confirm that the App has been running on the phone and the relevant reminder function has been opened; Message notification and authority confirmation in the mobile phone system have been opened.
Q: How can add devices or configure my network?
A:
The camera can be connected to both the monitor and the application. Generally, it connects to the monitor by default.
Q: The sound and cry detection function doesn’t work.
A:
The sound detection interval is 1 minute; after the sound triggers the alarm, the interval is 1 minute again to avoid frequent alarms. The cry detection function can detect most babies crying. This function uses a sound filtering algorithm, so some crying may not trigger the ‘cry detection’ function.
Please follow the steps below to connect the camera to the application.
- 1. Make sure the Wi-Fi network is a 2.4GHz network, as the camera does not support 5GHz Wi-Fi.
- 2. Download the appropriate application on your phone. Register a new account to sign in or sign in directly.
- 3. Use the needle to reset the camera until the red status light flashes slowly (you must connect the camera to the app within 2 minutes, or you must reboot the camera again).
- 4. Follow the step-by-step instructions on your smartphone to add the screen and scan the QR code with the camera.
Q: Can I set up motion tracking and alarm zones on the monitor?
A:
No, you need to set the motion tracking and alarm area through the ieGeek Cam APP.
Q: Why does the display make a bee sound?
A:
Because the monitor is too close to the camera, take it away from the camera more than 1 meter.
If you encounter any other problems, please send your order number and problem to [email protected], we will deal with your issue within 24hours.