ANRAN B01 B04 HD wifiセキュリティカメラ クイックスタートガイド

No products found.

含まれるもの

製品概要

CAUTION: Please insert the Micro SD Card according to thedirection shown in the diagram. Micro SD Card might JAM ifinserted incorrectly and device could be damaged.

SD Card Port: Support micro SD card for local storage (Max128GB)

Reset button: Used to restore the camera to factory settings(Press and hold on 5-8s)

CloudEdgeアプリのインストールとセットアップ

Download CloudEdge App(iOS&Android)

カメラの取り付け

高さと場所を選択

Hang anranCam 7-10 ft (2-3 m) above the ground. This heightmaximizes the detection range of the motion detection ofanranCam.Avoid placing anranCam under direct sunlight.

設置場所でのWifi信号のテスト

Use cell phone to test Wifi signal quality at the installationposition before installing camera, make sure the Wifi router canprovide good Wifi signal.

アカウント登録

1. Open the APP to sign up an account. Go to the login interface.
   and click “Sign Up”.
2. Sign up with your email address, and click “Next”

3.Set up an “Nickname” and “Password” for your APP, click “Doneto complete.

カメラのWiFiを設定する

1. Put both of your mobile phone and camera near therouterand the distance should be Within a 5 meters distance.

Note: wifi camera can only connect to 2.4 Ghz WiFi signal.Do not support 5Ghz WiFi. Therefore, it only needs to connect tothe WiFi signal of the family in 2.4GHz frequency band for normause.

2.Log in to “CloudEdge”, then tap the “+” icon in the center. Tap“Camera” to add device.

3.Reset the device and wait for a flashing RED indicator light.then tap“Next”

4.Selecting the Wi-Fi the device needs to connected with (yourhome Wi-Fi), input the password and click “Next”.

5.Using the device to scan the QR code on the mobile phoneaccording to the operation the figure shows, then proceed tothe next step after hearing the prompt tone.

6.After the network configuration is successful, set the nameand password for the device to add successfully; then you canview the camera screen in real time

よくあるご質問

満足ステートメント

FCC声明

This device complies with Part 15 of the FCC Rules. Operation issubject to the following two conditions: (1) this device may not causeharmful interference, and (2) this device must accept any interference received, including interference that may cause undesiredoperation.

Warning: Changes or modifications not expressly approved by theparty responsible for compliance could void the user’s authority tooperate the equipment.

Note: This equipment has been tested and found to comply with thelimits for a Class B digital device, pursuant to Part 15 of the FCCRules. These limits are designed to provide reasonable protectionagainst harmfulinterference in a residential installation.This equipment generates uses and can radiate radio frequencyenergy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communica-tions. However, there is no guarantee that interference will not occurin a particular installation. lf this equipment does cause harmfulinterference to radio or television reception, which can bedetermined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more ofthe following measures: (1) Reorient or relocate the receivingantenna.(2) lncrease the separation between the equipment andreceiver.(3) Connect the equipment into an outlet on a circuitdifferent from that to which the receiver is connected. (4) Consult thedealer or an experienced radio/ TV technician for help.

FCC無線周波数暴露ステートメント

The device has been evaluated to meet general RF exposurerequirements.The device
can be used in fixed/mobile exposure condition. The min separationdistance is 20cm.

お知らせシールドケーブル

All connections to other computing devices must be made usingshielded cables to
maintain compliance with FCC regulations.