ieGeek Bell J5 ドアベルカメラ ユーザーマニュアル

1.アフターサービス

ieGeekバッテリーWIFIセキュリティカメラをお買い上げいただきありがとうございます。弊社は12ヶ月の保証を提供しております。何か問題やご提案がございましたら、お気軽にAmazonのメッセージでお問い合わせいただくか、弊社の公式メールボックス([email protected])にメールをお送りください。最高のサービスを提供します。

注：

カメラは2.4GHz WI-Flのみ対応で、5GHz WIFIには対応していない。

Wi-Fiの信号強度が85%以上であることを確認してください。カメラが信号源から遠い場合、初回接続に成功しません。

• ルーターに接続されているデバイスが多すぎると、IPアドレスが競合するため、カメラはWi-Fi接続に失敗します。
• このワイヤレスカメラはPCブラウザとソフトウェアに対応していません。
• このワイヤレスカメラは、Wi-Fi切断時のイベント録画に対応しています。
• ビデオ再生はCloudEdge APPでのみ動作します。サードパーティ製プレーヤーには対応していません。
• 手動スナップショットと録画ファイルはモバイルに保存されます。イベントのスナップショットファイルはクラウドに保存されます。イベント記録ファイルはマイクロSDカードに保存されます。
• SDカードからライブ映像や録画したビデオを見ると、バッテリーの電力を消費します。

2. What’s in the box

3. Meet the doorbell

Note: The doorbell works with both 12V-24Y AC and 12V DC hardwire power sources. Either wire can be connected to either terminal. The cable order doesn’t matter.

Tips: Please turn on the two permissions below when using this app for the first time.

1. Allow the ‘CloudEdge’ APP to access mobile cellular data and wireless LAN, or it will fail to add a doorbell.

2. Allow the ‘CloudEdge’ APP to receive a pushed message, or the cellphone will not receive an alarm push when motion detection or audible alarm is triggered.

4. Meet the chime

5. Set up your doorbell

1. Attach the wires from the provided power adapter to the terminals on the rear of your doorbell. And tighten the terminal screws with the screwdriver. Each wire can be connected to each power terminal. The cable order doesn’t matter.

2. Plug the adapter into your AC outlet. Install the doorbell within 30 feet of your 2.4GHz WiFi router. It is suggested that you test your doorbell prior to physical installation.

3. Download and install the ‘CloudEdge’ app on your smartphone. Launch the App and register an account with your mobile phone number or email ID.

4. Register Account: New users need to register by e-mail, click Register, and follow the steps to complete the registration of the account, then log in.

注：

When registering a new account, please choose the region in which you are actually in. (Different registered regions can’t share the doorbell.)Please choose to register by e-mail.

5. Start the Wi-Fi configuration following the in-app instructions or referring to the below tutorial steps

6. LED indicator explanation:

6. Live-view

Tap on the Home page devices to watch the live view from your doorbell.

注：

Live viewing will not trigger device recording in Event recording mode.

7. Settings

7.1 APP Interface Introduction

7.2 Alert Settings

PIR’s’ Motion Detection’ is by default, and the default sensitivity is medium, but it is adjustable.

Alert settings steps:Setting(…)’ – >’Alarm Settings’ ->’Motion Detection

ヒント検出距離は4メートル（13フィート）です。

Note: Higher sensitivity offers a longer detecting distance, but it would lead to more false alarms. You are advised to set up the sensitivity level to ‘Medium’ when you install the doorbell outdoors.

7.2 Device Sharing

Warming: When you have a sharing, please make sure the APP account is registered in the same regions. Otherwise, you won’t share successfully! Other users can only live view & playback. All users can receive doorbell calls and alarm notifications(Need to open“receive notifications).

Sharing Steps: Settings (…)-> Device Share –> Tapon’Add’–> Choose“ScanQR Code’Acountshare

Method 1: Sharing by account searching
Tap on“Account’ –> Typein accountID –> ConfirmSharing –>Friends accept sharing

Method 2: Sharing by QRcode scanning. Tap on Scan QR code’–>Scan friends’ QR code –>Confirm Sharing –> Friends accept sharing.

Note: The new users can find their QR codes in the App and let the administrator scan the QR code and share the device

How do you find your QR code?

(Run CloudEdgeApp’–>Tapon” Tap on“!–> Tap on My QR Code”–> Let the administrator scan your QR Code.

8. Recording

Your doorbell comes with Event recording by default. lt will record visitor calls and motion detection events. You can also enable Full-day recording in the Settings -> SD Card.

9.History layback

Tap History to play the videos recorded on the MicroSD card.

1. Time Line:

Slide the timeline to the left or right to locate video recordings according to the time period. The green bar stands for video length, and The yellow dot stands for the alarm point when someone has pressed the doorbell button. The red dot stands for the alarm point when a motion has been detected.

2. Calendar:

Check video history by date. The numbers in green stand for the dates that have video recordings.

3. Screenshot:

Tap to capture a photo and save it to Me -> Pictures & Videos, Where you can share it with others

4. Record:

Tap to start recording a video, tap again to end, and save to Me -> Pictures & Videos, Where you share the video clips with others.

5. Alarm:

Tap the listed alarm records to locate and display each alarm video quickly. Stands for visitor call events; it stands for motion detection recordings.

6. Timeline Zoom:

Slide upward to zoom in on the timeline and downward to zoom out.

10. Connect the Chime

1. Supply power to the chime

The chime can be powered by a USB-compatible power source(DC5V 1A) or by the USB port on your computer.

2. Click the reset button

Click on RESET only once, and you will see the chime indicator flashing blue, indicating the chime is in pairing mode

3. Press the doorbell button

Press the doorbell button, and the chime will sound. If pairing is successful, the indicator on the chime will be in solid blue.

4. Chime settings

You can enter the chime setting page following the below setting steps so as to mute the ChimeReminder, select ringtones, adjust the chime volume, or unbind the connection with the doorbell.

注：

1. Your doorbell communicates with the chime via Radio Frequency but not WiFi

2. You can assign different chimes as needed.

3. Press and hold the RESET button on the chime for 5 seconds til the indicator flashes blue three times, and you can also release the connection between the chime and its connected doorbell.

11.設置方法

The video doorbell works with a 12V DC power source (power adapter provided), as well as an existing 12V~24V AC hardwire power source. It enables you to make use of your legacy doorbell wiring for retrofit installation.

注：

For retrofit installation, you need to bypass your indoor mechanical chime so as to provide sufficient power for the new video doorbell.

11.1 Retro-fit installation (Optional)

To replace your existing doorbell and mechanical chime, please follow below installation steps:

1. Shut off the master circuit breaker in your house.

2. Bypass your indoor chime with the provided jumper.

In most cases, the existing doorbell circuit looks similar to the image below. Remove the cover of the indoor chime and loosen the “FRONT” and “TRANS terminal screws. Use the provided jumper to connect the two terminals and replace the chime cover.

3. Select a location for your video doorbell.

Determine the mounting position of the doorbell. Check if you can reuse the existing holes on the wall. If not, drill new holes to mount your video doorbell. It is suggested to mount the doorbell at least 4 feet (120 cm) above the ground for optimal angle of view and best motion detection performance.

(Optional) Use the 20° angle mount as a supplementary mounting bracket to adjust the viewing angle towards to fit your viewing preference.

4. Replace your existing doorbell.

5. Restore power at the breaker, and your doorbell is ready for use.

11.2 Hardwire installation

Hardwire your doorbell with the provided DC12V power adapter.

12. Trouble Shooting

11. Specification

ビデオ・ドアベル

ビデオ＆オーディオ

ストレージ

ネットワーク

APP

一般

室内チャイム

12. FAQ

Q1: Does a battery power the video doorbell?

A1: No, this video doorbell requires a constant hardwire power supply. Compared to battery-powered doorbells, this wired video doorbell has more advanced features, like supporting full-day recording, no delay, and quick response to visitor calls. It is smaller in dimension, fitting into narrow door frames.

Q2: How do you connect the hardware to the doorbell? Does the cable order matter?

A2: Your doorbell works with both DC 12V and AC 12V – 24V hardwire power sources. There are 2terminal screws on the rear of your doorbell, and you can connect each wire to each power terminal screw. The cable order doesn’t matter.

Q3: I found a Micro USB port near the Micro SD Slot; what’s it for?

A3: You can power up the doorbell with the Micro USB port using a USB-compatible charger and cable. It is designed mainly for product testing in the factory.

Q4: What’s the Wi-Fi range of the video doorbell?

A4: The video doorbell works with any 2.4GHz wireless Wi-Fi router, mesh system, or modem. In Outfielotest, it works well in most 3000saft houses. The Wi-Fi range may vary because of different WiFi transmit power, transmission distance, and wall blocks in between.

Q5: I installed my video doorbell, but the video or audio quality is poor.

A5: ln live view interface, WiFi status will be listed. It is suggested to ensure the Wi-Fi status is more than 70% so as to get your doorbell to work as expected. If you think your problem is caused by low Wi-Fi signal strength, try moving your Wi-Fi router closer or adding one Wi-Fi Booster to extend your Wi-Fi range.

Q6: Does the video doorbell work with the existing indoor mechanical chime?

A6: No. The doorbell comes with a USB-compatible wireless chime to notify people when your visitor presses the doorbell button. If you have an existing indoor chime, please use the provided jumper to bypass the existing chime so as to provide sufficient power to the new video doorbell.

Q7: How many wireless chimes can be paired with one video doorbell?

A7: You can add as many wireless chimes as you wish on one video doorbell.

Q8: Does it support customized Motion Detection Zones

A8: Yes, it does. Go to Settings – Alarm Setting – Motion detection – Alarm Area. Use your fingertips draw one or more customized motion detection zones and save your settings the orange zones are motion detection zones

Q9: How does the video doorbell detect the motions? Can motion detection be disabled?

A9: The doorbell camera detects motion through the full-image pixel contrast; it will further undergo anuman-shape detection to reduce the false alarm rate. You can adjust the motion detection sensitivity, customize the detection zone, schedule alarm intervals, and disable motion detection accordingly due to various user scenarios.

Q10: Does the doorbell support cloud storage?

A10: Your doorbell supports Micro SD card storage as well as cloud storage. You can activate the cloud storage service in the App. There is a 7-day free cloud recording trial service. Please note that cloud storage only supports event recording but not full-day recording.