FCC 声明
本设备已经过测试，符合 FCC 规则第 15 部分对 B 类数字设备的限制要求。
这些限制旨在为住宅安装提供合理的保护，防止有害干扰。本设备会产生、使用和辐射无线电频率能量，如果不按照说明进行安装和使用，可能会对无线电通信造成有害干扰。但是，不能保证在特定安装环境中不会产生干扰。如果本设备确实对无线电或电视接收造成有害干扰（可通过关闭和打开设备来确定），建议用户尝试通过以下一项或多项措施来纠正干扰：
-调整接收天线的方向或位置。
-增加设备与接收器之间的距离。
-将设备连接到与接收器连接的电路不同的插座上。
-请向经销商或有经验的无线电/电视技术人员寻求帮助
不遵守规定可能导致用户无权操作本设备。(例如：在连接计算机或外围设备时，只能使用屏蔽接口电缆）。任何未经合规性责任方明确批准的更改或修改都可能导致用户无权操作本设备。本设备符合 FCC 规则第 15 部分的规定。操作须符合以下两个条件：
1) 本设备不得造成有害干扰
2) 本设备必须接受任何接收到的干扰，包括可能导致意外运行的干扰。
FCC Radiation Exposure Statement: The equipment complies with FCC Radiation exposure limits set forth for uncontrolled environments. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
FCC ID: 2AG7C-BABYIT(Camera)
FCC ID: 2AG7C-BABYIM(Monitor)
01/Overview
02/Download ‘ieGeek Cam’ APP
Method 1:
Download the ‘ieGeek Cam’ APP from the APP Store (iOS) or Google Play(Android)
Method 2:
Scan the QR-Code to download the App
03/connect the Camera to the APP
The camera can be connected to both the monitor and the app. Generally, it is connected to the monitor by default.
Follow the steps below to connect the camera to the App:
- 1. Make sure the Wi-Fi network is a 2.4 GHz network. as the camera doesn’t support 5GHz Wi-Fi.
- 2. Download the ieGeek cam App on your phone. Register a new account to log in or log in directly.
- 3. Use the needle to reset the camera for 5 seconds until you hear the ‘BOOGU’ beep, which means the camera has been reset; after 10-20 seconds, you will hear another beep, and the red light of the camera blinks slowly.
- 4. Follow the step instructions on your smartphone to add the camera, and scan the QR code with your camera.
04/connect the Camera to the Monitor
Turn on the power of the camera and the monitor, and then the camera will automatically connect to the monitor.
Note: If the connection to each other is not successful the first time, please use the needle to reset the camera and reconnect the monitor after the second beep of the camera. The connection is distance-limited, so make sure the distance between the camera and the monitor is no more than 300m.
Disconnect the camera from the monitor
- 1. Press the Menu button on the display screen, and select setting > Camera.
- 2. Long press the ok button on the display screen to release the binding.
Reconnect the camera to the monitor
1. Press the Menu button on the display screen, and select setting> Camera.
2. Long press the camera Pairing button until you hear the prompt tone
3. Press the ok button on the display screen to start pairing.
Note: If you have problems with connection, please feel free to contact [email protected] for one-on-one customer service guidance.
Connect two cameras to the monitor.
Follow the step above to connect the two cameras in turn. Two screens will appear on the monitor.
Press the back key for camera selection(a small camera icon flashes on the screen).
Press ←or→ for camera selection, then press the ok key to remotely control the selected camera (split view).
Press the ok key again to enter the selected camera in full-screen mode.
Press the back key to reselect the camera.
05/General Settings
Set up volume
1. Press Menu button on the display screen, and select and press ok to enter the interface
2. Press the UP and DoWN direction buttons to adjust the volume.
Set up brightness
1. Press the Menu button on the display screen, select, and press ok to enter the interface.
2. Press the UP and DOWN direction buttons to adjust brightness.
Set up time
1. Press the Menu button on the display screen and select Date and Time.
2. Press the Direction buttons to change the date, time, and time displaying mode.
Set up language
1. Press the Menu button on the display screen and select Language
2. Select the language you need
Set up sleep mode.
You can set up sleep mode to increase standby time.
1. Press the Menu button on the display screen and select Sleep mode.
2. Select Sleep mode as 1 minute, 5 minutes, 10 minutes, 30 minutes, 60 minutes or off.
Setting camera status indicator
1. Press the Menu button on the display screen, select and press the ok button to enter the interface
2. Press the left and right arrow keys to select on or off.
SD card
1. Press the Menu button on the display screen, and select > SD card management. Then, you can view the total capacity and remaining capacity of your SD card.
2. (Optional) You can format the SD card as you need, but make sure that the important data is backed up.
请注意：
This product does not support hot-swapping.
Please insert the SD card before powering it or unplug it after power off.
Upgrade
Make sure your camera is connected to a 2.4 GHz Wi-Fi. You can upgrade your camera when the upgraded alarm appears. Or press the Menu button on the display screen and select Device information to check whether it needs to be upgraded.
Low battery alarm
When the camera is low on battery, the low battery alarm will appear on the display screen. Please change the display as soon as possible.
Motion Tracking & Alarm Area
1. Motion Tracking: Open the ieGeek cam app, click your device, click the pinion icon in the upper right corner, select Motion Tracking, and open it.
2. Alarm Area: Open the ieGeek cam app, click your device, click the pinion icon in the upper right corner, and select Alarm Management>Motion Detection>Alarm Area.
Onvif Settings
Open the ieGeek cam app, click your device, click the pinion icon in the upper right corner, and select Onvif Setting, and set a password to enable this function.
06/FAQ
Q: The monitor cannot be previewed properly?
A:
Check whether the monitor has been connected to the camera. If not, pair the camera and the monitor first.
Q: Cannot find the pairing button?
A:
The pairing button is the call button of the camera. Long press the button for 3 seconds, and follow the step instructions of the display. (To enter the pairing interface of the display, press the Menu button on the display screen and select Camera Management.)
Q: What if the monitor screen is stuck and it doesn’t work while pressing any buttons?
A:
Reset your monitor with the needle, and then long-press the power button of your monitor to restart it.
Q: Why can’t I get the notifications with my cell phone App when I connect the camera to the monitor?
A:
Please confirm that the App has been running on the phone and the relevant reminder function has been opened; Message notification and authority confirmation in the mobile phone system have been opened.
Q: How can add devices or configure my network?
A:
The camera can be connected to both the monitor and the application. Generally, it connects to the monitor by default.
Q: The sound and cry detection function doesn’t work.
A:
The sound detection interval is 1 minute; after the sound triggers the alarm, the interval is 1 minute again to avoid frequent alarms. The cry detection function can detect most babies crying. This function uses a sound filtering algorithm, so some crying may not trigger the ‘cry detection’ function.
Please follow the steps below to connect the camera to the application.
- 1. Make sure the Wi-Fi network is a 2.4GHz network, as the camera does not support 5GHz Wi-Fi.
- 2. Download the appropriate application on your phone. Register a new account to sign in or sign in directly.
- 3. Use the needle to reset the camera until the red status light flashes slowly (you must connect the camera to the app within 2 minutes, or you must reboot the camera again).
- 4. Follow the step-by-step instructions on your smartphone to add the screen and scan the QR code with the camera.
Q: Can I set up motion tracking and alarm zones on the monitor?
A:
No, you need to set the motion tracking and alarm area through the ieGeek Cam APP.
Q: Why does the display make a bee sound?
A:
Because the monitor is too close to the camera, take it away from the camera more than 1 meter.
If you encounter any other problems, please send your order number and problem to [email protected], we will deal with your issue within 24hours.