TECGUUD 5SM Baby Monitor User Guide

Safety Instructions and Warnings

Hazard Warnings: Potential Risk of Strangulation

• Please be aware that children are at risk of strangulation and suffocation accidents caused by rope entanglement.
• Please keep power cords away from children; maintain a distance of at least 3.5 feet (1m)
• Do not allow children to use this product as a toy without supervision.
• Please do not leave the camera in the baby cot or safety fence.
• This baby monitor kit is a monitoring aid and cannot replace the functions and responsibilities of adult supervision.
• Do not leave your infant unattended or alone at home. Infants need the constant care and attention of adults.
• Do not use this product in an environment that could potentially leak flammable gas or expose the product to rain or humid conditions.

1. Meet the Camera

Note:

The camera needs to be plugged into a power source before it can be used.

Please use the original AC adapter and power cord (3M)to power the camera.

2. Meet the monitor

3. Charge Your Monitor

Precautions:

1. The monitor comes with a built-in battery that can last up to 6 hours of continuous use after a full charge. When the battery is low, it will pop up a low power alert.

2. Please use the original AC adapter and power cord(1M) for battery recharge. It takes about 5 hours to fully charge the monitor.

3. Do not use this product on a sloping or unstable surface, keep it away from heat sources to avoid possible damage, and do not place it near or on any electrical appliances

4. Do not allow children to use this product as a toy without supervision.

4. App Download

Search’ Cloudot ‘In the app stores or scan the QR codes below to download the app.

Register a user account and log in. And you will be able to add the camera to your APP account.

5. Set up Wi-Fi for the Camera

The camera can be paired with the monitor through its private AP network, with up to 150 meters of wireless intercom range. You can also add the camera to your account, setting up Wi-Fi so as to view & control the camera remotely through mobile devices

Steps to set up a camera in your App:

1. Plug in to supply power to the camera. Press & hold the reset button for 5 seconds till you hear the tone promoted.

2. Confirm the LED indicator blinks red. Now you have 2 minutes to set up your camera.

3. Set up the camera following the prompted in-app instructions.

4. Adding the camera completes, and the indicator light turns to solid blue.

Note:

Please operate the process near your Wi-Fi router.

Make sure your phone is connecting to a 2.4GHz Wi-Fi.

Make sure the camera is turned on, and its indicator LED is flashing red.lf not, press and hold RESET for 5 seconds.

Ensure the Wi-Fi signal is good, and the Wi-Fi password is correct.

6.Pair with Monitor

The camera is pre-paired with its monitor to work as asystem. The transmission range is limited by distance.Make sure the distance between them is within 150m(500 ft)

Disconnect the camera to the monitor:

1.Click ‘MENU’> select > click ‘OK’ > Click and enter into camera management.

2.Long press OK button on the monitor to release the bond.

Reconnect the camera to the monitor:

1.Click ‘MENU’ > select > click ‘OK’ > Click and enter into camera management.

2.Long press PAlR button on the camera till you hear aprompt tone.

3.Click the OK button on the monitor to start pairing

7.Use Your Baby Monitor

Rotate the camera

When the camera is powered on, press direction buttons on the monitor, and you can rotate the camera horizon-tally or vertically, for a better view angle.

Adjust speaker volume

1.Click ‘MENU’ button to display the icon dock.

2.Adjust speaker volume with up & down button.

Display brightness

1.Click ‘MENU’ button to display the icon dock.

2.Adjust brightness with up & down button.

Photo & video

Insert a Micro-SD memory card (Max 128GB) to your monitor, and you will be able to record photos and video clips.

Play music

Turn on/off camera indicator

1.Click MENU’ button to display the icon dock.

2.Switch on/off the camera indicator light with the left/right button.

Configurações

8. Troubleshooting

Q1: The monitor cannot be previewed properly?

A1:Check whether the monitor has been connected to the camera. If not, pair the camera and the monitor first.

Q2: What if the monitor screen is stuck and it doesn’t work while pressing any buttons?

A2: Press the reset button of your monitor with the pin, and then long-press the power button of your monitor to restart it.

Q3: Why can it not detect my SD card?

A3: Make sure the Micro SD card is properly installed and try formatting the SD card in FAT32 format before using it.

Q4: Why can’t l get the notifications with my cell phone App when I connect the camera to the monitor?

A4: To be able to receive visitor notifications properly on your smartphone, it is important to allow all notifications and permissions. You can check this from your phone settings regarding app permissions within the CloudEdge app.

Q5: Why does the monitor lose connection with the camera after the camera is connected to the CloudEdge App?

A5: The monitor has a 2-minute interruption time when the camera is reset, and it will automatically resume after 2 minutes. If it doesn’t recover, try to pair the monitor and camera again.