Morecam J7 Doorbell Camera User Guide

image 952

Note: Manual contents are subject to change without notice inaccordance with our polivy of continuous product improvement.

1. Charge your doorbell with your phone charger.

Plug in the charger

Please charge your doorbell with a USB-compatible phone charger(not provided) and the provided charging cable. The LED indicator near the MicroUSB port will glow blue once fully charged.

image 32
image 724

2. Supply power to the chime.

Powered by three AA batteries

Three units of AA batteries are required to make your indoor chime 100% wire-free. And you will be free to place your chime in almost anywhere indoors

Please mind the electrodes when installing batteries!

image 725

Powered by DC5V Charger.

You can also plug in the provided USB cable and connect the chime to your DC 5V 1A~2A phone charger.

image 726

3.Set up your doorbell in the CloudEdge app

Download the CloudEdge app

Search ‘CloudEdge’in the app stores or scan below QR codes to download the app

image 727

Switch on your doorbell

Remove the wall mounting bracket and the right-side silicone cover, and switch on the power for your doorbell. The LED indicator around the doorbell button will be red (once per second), and it is ready for network setting

image 728

Set up your doorbell.

In the ‘CloudEdge’ app, log in or create a user account to log in. Tap select Doorbell, and complete the setup following the in-app instructions

image 729

Tips:

1). Please operate the setup near your Wi-Fi router.

2). Make sure your phone is connecting to a 2.4GHz Wi-Fi

3). Make sure the doorbell is turned on and its indicator LED is flashing red. If not, press and hold RESET for 5 seconds.

4). Ensure the Wi-Fi signal is good, and the Wi-Fi password is correct.

Doorbell indicator explanation.

image 730

4. Connect the indoor chime

Click the reset button.

Click RESET on the chime, and the chime indicator on the left will flash red for 20 seconds, indicating that the chime is in pairing mode

image 731

Press your doorbell to pair up

Press the doorbell button to send a pairing signal, and your chime will sound to react, together with its blue LED flashing. Chime pairing succeeds

image 732

Chime settings.

Ringtone selection.

Click to change ringtone (4 ringtones available)

Volume control button.

Click to control volume:

level 1: 110 dB;
level 2: 100 dB;
level 3: 90 dB;
level 4: 80 dB

Settings

Click to enter/quit pairing mode; Press & hold for 5 seconds to restore factory defaults

image 733

5. Install your smart doorbell

Select a location.

image 734

It is suggested to mount the doorbell at least 4 feet (120 cm) above the ground for optimal angle of view and best motion detection performance.

Install at an angle (Optional)

You can purchase the following angled brackets so as to point your doorbell to a specific view angle.

image 735

Mark the screw holes

Take apart the wall mount from your doorbell and use it as a template, mark the location of the two mounting holes on your wall.

image 736

Install the wall mount

Screw your bracket into the wooden wall with the provided mounting screws.
if installing on stucco, brick, or concrete, drill holes in your wall, then insert the included anchors before driving in the mounting screws

image 737

Mount your doorbell

Attach your doorbell to the mounting bracket and then snap the doorbell to make sure it reaches the bottom. Then secure it with the provided star-shaped security screw, using the provided screwdriver bit

image 738

One more thing

Kindly note the anti-theft alarm in the doorbell settings

image 739

Tamper alert on

Once the doorbell is detached from the bracket, a 30-second alarm will be triggered. Meanwhile, video recording will be activated, and alarm notifications will be pushed to the owner’s APP account.

Tamper alert off

The owner can disable the tamper alarm in doorbell settings and detach the doorbell for battery recharging or maintenance

12. Product Specifications

Video Doorbell Model No.:Bell J7

CameraFull-HD Camera
Effective pixels1920(H) x 1080(V)
IR LEDHigh power dot-array IR LED x 1
View angle145°
Motion detect range100° (Max 5m)
Motion sensitivity5 level sensitivity settable
Alarm triggerCall button, motion detect, anti-theft alarm
Wi-Fi2.4 ~ 2.4835 GHz WIFI (IEEE802.11b/g/n)
Video recordingVideo clips against events
AudioFull duplex 2-way audio
StorageSD card (Max. 128G)
Cloud storageYes (7-days-free trial)
Power supplyBuilt-in rechargeable Li-ion battery
Battery capacity4,500mAh
Ingress protectionIP65
Operating Temp.-10℃ to 50℃
Dimensions34.5 x 56 x 134.6mm
Net weight125.8g (Battery Included)

Wireless Chime Model No.: Chime06

Power source 1DC 5V 1A (from Micro USB)
Power source 2AA LR6 1.5V battery x 3 units
Consumption0.4W
Ringtones4 ringtones optional
Connection typeRadio frequency 433MHz
Place of useIndoor
Blue LED flashingPairing mode
Red LED flashingWorking normally
Blue LED flashing twiceReset factory default succeeds
Working Temp.-10℃ ~ 50℃
Humidity<90%, no condensation
Dimension75.5 x 75 x 28mm
Weight70g (Exclude batteries)

Trouble Shooting

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top