XTU J1 Doorbell Camera User Guide

image 782

1. What’s in the box

Please consult the below checklist for all the components.

image 783

2. Meet the doorbell

image 784
  1. 2MP Camera
  2. PIR Motion Sensor
  3. Speakers
  4. Indicating LED
  5. Doorbell Button
  6. Microphone
  7. Charging Indicator
  8. Micro USB Port
  9. Reset
  10. Wall-mount bracket
  11. SD Card Slot
  12. Battery Compartment

3. Meet the chime

image 785
  1. Speakers
  2. Reset
  3. LED Indicator
  4. USB Port (Type-A/M)

4. Battery installation

The batteries are pre-installed in the doorbell. If you have taken out the batteries, please note the electrodes when installing batteries. Please insert the batteries with positive poles upward!

image 786

NOTE:

Improper battery installation will cause damage to the internal components and may result in serious injury

5. Battery charging

The batteries inside the doorbell are not fully charged in accordance with transportation safety regulations.

Please charge the batteries with a USB-compatible wall charger (not included) and the provided USB cable for about 8~10 hours prior to Wi-Fi configuration and installation.

image 787

6. Download the app

Download and install the ‘CloudEdge’ app from Google Play or the App Store. The App is also available by scanning the QR codes on the right using your QR code scanner on your smartphone.

NOTE: Google Play is a trademark of Google Inc. App Store and is a service mark of Apple Inc.

image 788

7. wi-fi set up

Before you start the Wi-Fi configuration, please note the following:

  • 1). The doorbell works with 2.4 GHz Wi-Fi but not with 5 GHz Wi-Fi.
  • 2). Avoid using special characters or symbols like )(@~!#�%^&*…, either in your Wi-Fi name or password.
  • 3). Perform the configuration near your Wi-Fi router.

Launch the CloudEdge APP and register an account with your mobile phone number or email ID. Then start the Wi-Fi.

Before you start the Wi-Fi configuration, please note the following:

image 789
image 790
image 791

8. run a test

After setup, tap on the live view window in the app for a test. Then, take your doorbell outside to the installation spot and run a test there. Make sure the installation spot is covered by a strong 2.4 GHz Wi-Fi signal.

Note:

If the video quality from the doorbell outside is not as good as it was indoors, you may need to move your router closer to your installation spot or invest in a Wi-Fi extender.

9. Live view interface

image 792
1. Quit live viewing2. Setting menu3. Battery status
4. Volume on/off5. HD/SD switch6. Wi-Fi signal status
7. Stream bit rate8. Wi-Fi signal status9. Screenshot button
10. Speak to the scene11. Record on the phone12. Body detection on/off
13. Notification history14. Cloud storage service

10. leave a Voice message

You can leave a maximum 30-second voice message on the onboard memory of your doorbell so as to quickly respond to your visitor by a tap on your phone when you are not able to answer the doorbell call. The voice message function is available even without a pre-installed Micro-SD card.

STEPS:

Setting -> Basic function -> Host Leaves Message -> Record your message -> Hang off the incoming call and play the voice message.

image 793

11. Installation

Select location

image 794

Your doorbell has a 166-degree view angle and a 120-degree human detection range.

It is suggested to mount your doorbell at least 5 feet (160 cm) above the ground for the best angle of view and motion detection performance.

Mount your doorbell

1. Take out the wall mount by pushing from its back.

2. Mark the screw positions to mount the bracket.

3. Drive the screws into the anchors or directly into your wall until the bracket is tightly fastened on your wall.

image 795

4. (Optional) You can also use the double-sided tape that we provided instead of screws.

5.Attach your doorbell to the mountingbracket.Make sure it reaches the bottom, where you can hear a click.

6. Secure your doorbell with the provided star-shaped security screw and screwdriver set. Congratulations!

image 796

12. connect the chime

supply power to the chime

image 797

The chime can be powered by a USB-compatible phone charger (DC5V 1A). You can also plug the chime into the USB port on your PC/notebook to supply power.

Pair with doorbell

image 798

1.Tap on “···” and enter into Settings-> Basic function, select Wireless Chime page.(See to Picture.6)

2. Short-click on the reset button behind the chime(refer to Picture.4), and the LED indicator flashes blue, indicating the device is in pairing mode.

3. Tap the “Chime Pairing” button in the APP (refer to Picture.6), and the doorbell will send a wireless pairing signal to the chime. Pairing succeeds, and the indicator on the Chime will be in solid blue. All set! Congrats! You can push the doorbell button to test the result.

Select ringtone

Enter Settings->Wireless Chime; there are four ringtones available (refer to Picture.6).

Volume control

You can control the volume level for the chime in the Wireless Chime Pairing page (refer to Picture.6).

Unbind

1. Press and hold the reset button on the chime for about 5 seconds till the indicator flashes blue twice, and the chime will be restored to factory default.

2. You can also tap on “One-button Untie” (refer to Picture.6) in the APP to release the connection between the doorbells and the wireless chimes.

13.SHare device

You can share your doorbell with your family members and friends by following a few setting steps in your app.

STEPS:

Friends -> Search and add your friends to the contact list -> Back to Devices -> Enter into Settings -> Device Share.

image 799

NOTE:

1. There is no limitation on number of friends sharing one device.

2. Only the administrator has access to the settings menu. Other users can only live view & playback.

3. All users can receive doorbell calls and alarm notifications.

4. Many users can access the doorbell simultaneously to live view or playback.

14. Specification

VIDEO DOORBELL

Video & Audio

Image Sensor1/2.7”CMOS(2.0MP)
OSHisilicon Lite-OS
Resolution1920×1080
StreamHD/SD dual stream
Infrared LEDHigh-power IR LED with ICR
Lens1.7mm/F2.0
Angle of view166°
Min. illumin.Color: 0.01LUX: B&W:0.001LUX
WDRDigital WDR
Audio2-way audio with noise cancellation

Storage

Storage TypeMicro SD Card (Max 128G)
Cloud storagesupport
RecordingTriggered by PIR motion sensor

Network

Wifi Frequency2.4 GHz- 2.4835 GHz
StandardsIEEE 802.11b/g/n
Live View SpeedWithin 3-4 Sec

APP

App NameCloudEdge
OSOS, Android
Remote ViewWithin 2-4 sec
NotificationPush notification within 2~4 sec

General

Working Temp&Humidity-10°C-50°C(14F~122°F);
<90%(No condensation)
Power SourceLithium 18650 Battery *2
Standby Current300uA
Working Current250mA
Standby Time3 – 4 Months
Working Time1.5~ 2 Months(10 times wake up per day)
Battery ChargingDC5V1A-2A(Micro USB Port)
Firmware UpgradeOTA (on the air)

INDOOR CHIME

Power sourceDC 5V 1A
Power portUSB (Type-A)
Consumption0.2W
RingtonesFour ringtones optional
VolumeMax100dB
Volume controlLow(mute), middle, high
Connection typeRadio frequency
Frequency433MHz-868MHz
LEDFlashing blue: pairing mode
Solid blue: power on/pairing succeeded
Flash blue twice: reset to factory default
Working Temp-10°C~50°C(14°F~122°F)

15. Troubleshooting

Q1: Why did I fail to set up Wi-Fi for the doorbell?

A1:

â‘  .The device works with 2.4GHz Wi-Fi only but does not support 5GHz Wi-Fi.

â‘¡ .The Wi-Fi network is not good; try to keep the camera near the Wi-Fi router when setting up.

â‘¢ .The Wi-Fi password is wrong. Please check if there are special characters in the password or if the network is specially encrypted.

Q2: How do I know if I have 2.4G or 5G Wi-Fi?

A2: Please check the user manual of your Router or call the network operator for help.

Q3: It have to be on the same WiFi to see the camera, or is it over the internet from anywhere?

A3: You can view the camera from anywhere if your camera is well connected to the internet.

Q4: Do any of the recordings get saved to the cloud? Or is it mainly saved in the built-in SD card?

A4:It supports SD card recording as well as cloud storage. You can activate the cloud storage service in the App.

Q5: What happens when the SD is full?

A5: When the memory card is full, the camera automatically erases the oldest footage.

Q6: Does it work with Google Home or Alexa?

A6:Sorry, this model does not support Google Home or Alexa.

Q7: Why does it lose connection to wifi?

A7: Please check the network connection of your phone and the Wi-Fi router. If the network signal is not strong, you may need to move your router closer to the device or invest in an extender.

Q8: Can motion detection be disabled?

A8:Yes, sure. The recording is triggered by detected motions. You can set up the sensitivity or disable motion detection in the settings menu.

Q9:Do we get a charger for the batteries?

A9:Battery charger is not included. Please charge the batteries with a USB-compatible charger(DC5V 1A~2A) for about 8-10 hours.

Q10: Can we have two or more doorbells at the same residence?

A10:Yes, you can add more than one device at the same residence.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top