FCC 성명서
이 장비는 테스트를 거쳐 FCC 규정의 파트 15에 따라 클래스 B 디지털 기기에 대한 제한 사항을 준수하는 것으로 확인되었습니다.
이러한 제한은 주거용 설치 시 유해한 간섭에 대한 합리적인 보호를 제공하기 위해 마련되었습니다. 이 장비는 무선 주파수 에너지를 생성, 사용 및 방출할 수 있으며, 지침에 따라 설치 및 사용하지 않을 경우 무선 통신에 유해한 간섭을 일으킬 수 있습니다. 그러나 특정 설치 환경에서 간섭이 발생하지 않는다고 보장할 수는 없습니다. 이 장비가 라디오 또는 텔레비전 수신에 유해한 간섭을 일으키는 경우(장비를 껐다 켜서 확인할 수 있음), 사용자는 다음 조치 중 하나 이상을 사용하여 간섭을 수정하는 것이 좋습니다:
-수신 안테나의 방향을 바꾸거나 재배치합니다.
-장비와 수신기 사이의 거리를 늘립니다.
-수신기가 연결된 회로와 다른 회로의 콘센트에 장비를 연결합니다.
-대리점 또는 숙련된 라디오/TV 기술자에게 도움을 요청하세요.
규정을 준수하지 않을 경우 사용자의 장비 작동 권한이 무효화될 수 있습니다. (예: 컴퓨터 또는 주변 장치에 연결할 때는 차폐된 인터페이스 케이블만 사용). 규정 준수 책임이 있는 당사자가 명시적으로 승인하지 않은 변경 또는 수정은 사용자의 장비 작동 권한을 무효화할 수 있습니다. 이 장비는 FCC 규정의 파트 15를 준수합니다. 작동에는 다음 두 가지 조건이 적용됩니다:
1)이 장치는 유해한 간섭을 일으키지 않을 수 있습니다.
2) 이 장치는 원치 않는 작동을 유발할 수 있는 간섭을 포함하여 수신된 모든 간섭을 수용해야 합니다.
FCC 방사선 노출 진술서: 이 장비는 통제되지 않은 환경에 대해 규정된 FCC 방사선 노출 제한을 준수합니다. 이 장비는 라디에이터와 신체 사이에 최소 20cm의 거리를 두고 설치 및 작동해야 합니다.
FCC ID: 2AG7C-BABYIT(Camera)
FCC ID: 2AG7C-BABYIM(Monitor)
01/what’s in the Box
02/Overview
03/Download ‘ieGeek Cam’ APP
Method 1:
Download the ‘ieGeek Cam’ APP from the APP Store (iOS) or Google Play(Android)
Method 2:
Scan the QR-Code to download the App
04/connect the Camera to the APP
The camera can be connected to both the monitor and the app. Generally, it is connected to the monitor by default.
Follow the steps below to connect the camera to the App:
- 1. Make sure the Wi-Fi network is a 2.4 GHz network. as the camera doesn’t support 5GHz Wi-Fi.
- 2. Download the ieGeek cam App on your phone. Register a new account to log in or log in directly.
- 3. Use the needle to reset the camera for 5 seconds until you hear the ‘BOOGU’ beep, which means the camera has been reset; after 10-20 seconds, you will hear another beep, and the red light of the camera blinks slowly.
- 4. Follow the step instructions on your smartphone to add the camera, and scan the QR code with your camera.
Note: You can share the app with other people; the shared account and your account must belong to the same country.
05/connect the Camera to the Monitor
Turn on the power of the camera and the monitor, and then the camera will automatically connect to the monitor.
Note: If the connection to each other is not successful the first time, please use the needle to reset the camera and reconnect the monitor after the second beep of the camera. The connection is distance-limited, so make sure the distance between the camera and the monitor is no more than 300m.
06/Disconnect the camera from the monitor
- 1. Press the Menu button on the display screen, and select setting > Camera.
- 2. Long press the ok button on the display screen to release the binding.
07/Reconnect the camera to the monitor
1. Press the Menu button on the display screen, and select setting> Camera.
2. Long press the camera Pairing button until you hear the prompt tone
3. Press the ok button on the display screen to start pairing.
Note: If you have problems with connection, please feel free to contact [email protected] for on one customer service guidance.
Connect two cameras to the monitor.
Follow the step above to connect the two cameras in turn. Two screens will appear on the monitor.
Press the back key for camera selection(a small camera icon flashes on the screen).
Press ←or→ for camera selection, then press the ok key to remotely control the selected camera (split view).
Press the ok key again to enter the selected camera in full-screen mode.
Press the back key to reselect the camera.
08/General Settings
Set up volume
1. Press Menu button on the display screen, and select and press ok to enter the interface
2. Press the UP and DoWN direction buttons to adjust the volume.
Set up brightness
1. Press the Menu button on the display screen, select, and press ok to enter the interface.
2. Press the UP and DOWN direction buttons to adjust brightness.
Set up time
1. Press the Menu button on the display screen and select Date and Time.
2. Press the Direction buttons to change the date, time, and time displaying mode.
Set up language
1. Press the Menu button on the display screen and select Language
2. Select the language you need
Set up sleep mode.
You can set up sleep mode to increase standby time.
1. Press the Menu button on the display screen and select Sleep mode.
2. Select Sleep mode as 1 minute, 5 minutes, 10 minutes, 30 minutes, 60 minutes, or off.
Setting camera status indicator
1. Press the Menu button on the display screen, select and press the ok button to enter the interface
2. Press the left and right arrow keys to select on or off.
SD card
1. Press the Menu button on the display screen, and select > SD card management. Then, you can view the total capacity and remaining capacity of your SD card.
2. (Optional) You can format the SD card as you need, but make sure that the important data is backed up.
참고:
This product does not support hot-swapping.
Please insert the SD card before powering it or unplug it after power off.
Upgrade
Make sure your camera is connected to a 2.4 GHz Wi-Fi. You can upgrade your camera when the upgraded alarm appears. Or press the Menu button on the display screen and select Device information to check whether it needs to be upgraded.
Low battery alarm
When the camera is low on battery, the low battery alarm will appear on the display screen. Please change the display as soon as possible.
Motion Tracking & Alarm Area
1. Motion Tracking: Open the ieGeek cam app, click your device, click the pinion icon in the upper right corner, select Motion Tracking, and open it.
2. Alarm Area: Open the ieGeek cam app, click your device, click the pinion icon in the upper right corner, and select Alarm Management>Motion Detection>Alarm Area.
Onvif Settings
Open the ieGeek cam app, click your device, click the pinion icon in the upper right corner, and select Onvif Setting; you need to set a password to enable this function.
09/FAQ
Q: The monitor cannot be previewed properly?
A:
Check whether the monitor has been connected to the camera. If not, pair the camera and the monitor first.
Q: Cannot find the pairing button?
A:
The pairing button is the call button of the camera. Long press the button for 3 seconds, and follow the step instructions of the display. (To enter the pairing interface of the display, press the Menu button on the display screen and select Camera Management.)
Q: What if the monitor screen is stuck and it doesn’t work while pressing any buttons?
A:
Reset your monitor with the needle, and then long-press your monitor’s power button to restart it.
Q: Why can’t I get the notifications with my cell phone App when I connect the camera to the monitor?
A:
Please confirm that the App has been running on the phone and the relevant reminder function has been opened; Message notification and authority confirmation in the mobile phone system have been opened.
Q: How can I add devices or configure my network?
A:
The camera can be connected to both the monitor and the application. Generally, it connects to the monitor by default.
Q: The sound and cry detection function doesn’t work.
A:
The sound detection interval is 1 minute; after the sound triggers the alarm, the interval is 1 minute again to avoid fent alarms. The cry detection function can detect most babies crying. This function uses a sound filtering algorithm, so some crying may not trigger the ‘cry detection’ function.
Please follow the steps below to connect the camera to the application.
- 1. Make sure the Wi-Fi network is a 2.4GHz network, as the camera does not support 5GHz Wi-Fi.
- 2. Download the appropriate application on your phone. Register a new account to sign in or sign in directly.
- 3. Use the needle to reset the camera until the red status light flashes slowly (you must connect the camera to the app within 2 minutes, or you must reboot the camera again).
- 4. Follow the step-by-step instructions on your smartphone to add the screen and scan the QR code with the camera.
Q: Can I set up motion tracking and alarm zones on the monitor?
A:
No, you need to set the motion tracking and alarm area through the ieGeek Cam APP.
Q: Why does the display make a bee sound?
A:
Because the monitor is too close to the camera, take it away from the camera more than 1 meter.
If you encounter any other problems, please send your order number and problem to [email protected], we will deal with your issue within 24hours.