Camera Introduction
| 키 재설정 | 동영상에 사용할 사운드 캡처 |
| SD 카드 슬롯 | 로컬 SD 카드 저장소 지원(최대 128G) |
| 렌즈 | Support FHD resolution |
| 마이크 | Capture sound for your videos |
| 작업 상태 표시등 | Solid on red: Network is abnormal Flashing red slowly: Ready for Wi-Fi connection Flashing red quickly: Wi-Fi connecting Solid on blue: Wi-Fi connected Successfully |
| 스피커 | Two-way audio output |
앱 설치 및 계정 등록
Download ‘CloudEdge’ APP
Method 1: Download ‘CloudEdge’ and ‘ieGeek Cam’ APP from APP Store (iOS) or Google Play (Android);
Method 2: Scan the ‘CloudEdge’ APP QR code to download it.
Tips: Please turn on the 2 permissions below while using this app for the first time.
1. 'CloudEdge' 앱이 모바일 셀룰러 데이터 및 무선 LAN에 액세스할 수 있도록 허용하지 않으면 IP 카메라를 추가하지 못합니다.
2. 동작 감지 또는 청각적 알람이 트리거될 때 'CloudEdge' 앱이 푸시 메시지를 수신하도록 허용하지 않으면 휴대폰에 알람 푸시가 수신되지 않습니다.
Register Account
신규 사용자는 이메일로 등록해야 합니다. 구체적인 단계는 다음과 같습니다:
- 1. Click “Register”
- 2. Follow the steps to complete the registration of the account.
- 3.Log in.
참고:
•When registering a new account, please choose the region which you are actually in and the correct country code. (Different registered regions can’t share the camera.
•Please choose to register by e-mail.
How to Add a Camera to APP
Before Using:
1. Please insert the Micro SD card before powering it on; otherwise, the SD card can not be detected.
2. Put the camera and smartphone 1-3 ft (30-100 cm)away from the router to set Wi-Fi.
3. Make sure that the camera is using 2.4GHz Wi-Fi.
Wi-Fi Connection Steps
카메라가 Wi-Fi에 연결되지 않습니다.
1. Before adding a device, make sure that the device is in a state of slow flashing.red light. If the indicator status is abnormal, please restore the device to factory settings(long press and hold the device RESET button until you hear the ‘boogu’Sound)
2. Please make sure the Wi-Fi connection to the camera is 2.4GHz. In our experience, network connection fails in most cases when users use 5GHz WIFI.
3. Make sure the password correction of the Wi-Fi. (Note: The WiFi password cannot include a single quote, underline, space, and virgule.)
4. Check the number of devices your router connected. In general, the router has a connection limit. Once the devices that your router connected exceed its max limit numbers, other devices will not connect to the router.
5. Make sure the QR code on the phone screen is normal, and the distance between the phone and the camera lens is 10-15cm (3.9- 5.9 inches) during the scanning process.
6. After checking the above information, if the camera cannot connect to the Wi-Fi, please try to re-download the APP, reset the camera, restart the router, and then add the camera again.
7. If you tried all the steps but still had no luck, please message your order and problem to [email protected].
Mounting The Camera To The Wall
참고:
In order to obtain the best product performance and avoid unnecessary environmental disturbances, please pay attention to the following during the installation process:
•Try to avoid installing the product on the side of a lively road. Frequent pedestrians and vehicles will keep waking up the camera, resulting in frequent alarm messages.
•Do not install the product very far from the router; the product needs a good WI-FI signal to work properly.
Alert Settings
1. Motion Detection Settings
Enter the application -“Settings”-“Alert Settings”-“Motion Detection” interface, and you can adjust the motion detection settings.
1. Low belongs to the low gear sensitivity, with a motion detection distance of 4-5 meters.
2. Medium belongs to the Med gear sensitivity, with a motion detection distance of 5-8 meters.
3. High belongs to the high gear sensitivity, with a motion detection distance of 8-10 meters.
2. Noise Detection
The sound and light alarm is only effective at night. When the sound and light alarm is turned on, you can choose “sound alarm,” “white light alarm,” or “sound and light alarm,” three modes.
참고:
If the night alarm is disabled, the camera will only record black-and-white video at night.
Important Notes on Reducing False Alarms
1. Do not face the camera towards any objects with bright lights, including sunshine, bright lamplights, etc.
2. Do not place the camera near any outlets, including the air conditioner vents, humidifier outlet heat transfer vents of projectors, etc.
3. Do not install the camera in places with strong wind.
4. Do not face the camera towards a mirror.
5. Keep the camera at least 1 meter away from any wireless devices, including Wifi routers and phones in order to avoid wireless interference.
자주 묻는 질문
In the process of using this product, if you encounter the following problems, you can adjust the motion detection sensitivity to solve them.
•If the phone receives alarm messages too frequently, it is recommended to lower the motion detection level or set the alarm area.
•If you find that there are no moving objects in the alarm picture that the phone frequently receives, it may be due to factors such as changes in light and shadow in the motion detection range; it is recommended to lower the motion detection level or set the alarm area.